General Instructions (not device-specific) : Do not drag and drop your file to the email it does not open correctly for us. Afterward, send your base tune file as an attachment via email at and put your order number in the subject line. Please save this file as it is your original read and have it saved to the desktop (it is easier to find then). After the read is complete VCM Editor will automatically prompt you to save the file. Reading the factory tune will take 2-15 minutes depending on the vehicle. There is no reason for most vehicles to read this, and if you read it and then try to write it charges extra HPTuners credits to write the FSCM. Pictured below you will see you read the engine and transmission, you select to not read the FSCM. With the editor open you will select the green arrow which is the read function. You have to have the ignition key on the engine off. For this, you'll need to go out to the vehicle, plug in the MPVI3 to your laptop and vehicle OBD2 port, and open the VCM editor, select "Read Vehicle". Once you register your MPVI3 it is time to read your vehicle's base file. Once you receive your HPTuners MPVI3 tune you will need to make an account on HPTuners and register your device. In the picture below from the HPTuner website, it is the download on the right that is blue.Īn MPVI3 requires a wifi connection to read/write to the vehicle. You will go to to download the latest version of the VCM Suite Latest Beta. The editor is what you use to write tunes to the vehicle, and Scanner's purpose is to datalog. There are 2 programs you'll need to download, VCM Editor BETA, and VCM Scanner Beta these are part of the VCM Suite Latest Beta. You also use the interface to datalog so we can refine the tune to the vehicle. It communicates via the interface (MPVI2) communicating directly from a laptop(must be Windows-based not Apple/IOS) to the vehicle's OBD2 Port. Repeat steps a through c until your desired tuning goals have been met.HPTuners is the latest and greatest way of tuning using the MPVI3, rather than using a handheld programmer from which to load tunes. Use VCM Scanner to check the impact of your changes and verify that all performance and emissions characteristics of the vehicle remain within limits acceptable to the vehicle owner and required by law. Write the modified tune file back to the vehicle. This process usually has the following steps: Do not attempt to make any change to a vehicle's tune without thoroughly researching the potential impacts of the change. See Reading a Vehicle for instructions.ĬAUTION: Improperly tuning a vehicle can cause serious engine damage. In VCM Editor, read the current tune of the of the vehicle. Obtaining this "data log" will often provide valuable information in understanding the vehicle's current behavior. Once you have resolved as many DTCs as possible, the next step is usually to read of the vehicle's current sensor output using VCM Scanner. DO NOT proceed to the next step until you have resolved as many DTCs as possible and made note of those issues that cannot be resolved. IMPORTANT: Reading a vehicle will clear all DTCs, resulting in the loss of the troubleshooting information they contain. See Reading and Clearing DTCs for instructions. This makes it very difficult to tune the vehicle effectively. If there is a mechanical issue with the vehicle, it may affect performance and any performance data you want to monitor could be impacted. ![]() When you are ready to begin tuning, ALWAYS check the vehicle for diagnostic trouble codes (DTCs) before you do anything else. See the following topics for more information: You will only need to pay for the vehicles you actually tune and payment is not required until you flash your changes back to the vehicle. The VCM Suite is licensed on a "pay as you go" basis. 4.īefore you get started tuning vehicles, you may want to familiarize yourself with our licensing system. NOTE: Certain vehicles may require modifications to their VCM or special cables to allow reading and writing of tuning files. See Preparing a New Interface Device for Use. ![]() When you receive the device, prepare it for use. ![]() See Obtaining A New Interface Device for more information. If you do not already have such a device, follow these steps to obtain one and prepare it for use: The VCM Suite connects to vehicles using an interface device from HP Tuners. See Installing The Software for more information. If you don't already have an account on, create one now.ĭownload and install the VCM Suite. Follow these steps to get started with the VCM Suite: 1.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |